Timberline® Prestique® - Application Instructions (Metric)
Precautionary Notes These shingles are fiberglass, self-sealing asphalt shingles. Because of the natural characteristics of the high quality waterproofing material ... Read Content
CertainTeed StreakFighter Shingle Guide - FHA Products
CertainTeed shingles are available in a wide asphalt shingles. To make shingles resistant to algae, a unique zinc, can also provide resistance to algae, copper does not result in white spots or “blooming,” an unattractive phenomenon ... Read Here
SECTION 07 31 13
ASPHALT SHINGLES Display hidden notes 2.2 ASPHALT FIBERGLASS SHINGLES A. CertainTeed Landmark AR: Conforming to ASTM D 3018 Type I – Self-Sealing, UL Certification of ASTM D 3462, zinc coated steel, aluminum or chromated steel; minimum 3.8 inch (9.5mm) ... Access This Document
GAF Timberline Series Application Instructions (Tri-Lingual)
T '"45&/&34 Use only zinc-coated steel or aluminum, 10-12 gauge, Install GAF ridge cap shingles following the application instructions shown on the GAF ridge cap shingle wrapper or cut hip & ridge shingles from If old asphalt shingles are to remain in place, ... Fetch Here
ASPHALT SHINGLE PRODUCTS THAT CONFORM TO ASTM D 3161
ASPHALT SHINGLE PRODUCTS THAT CONFORM TO THE 2003 INTERNATIONAL RESIDENTIAL CODE (IRC) AND 2003 INTERNATIONAL BUILDING CODE (IBC), AND ASTM D 3161 MODIFIED TO 110 MPH As of December 31, 2007– Asphalt Shingles Verified to Pass ASTM D 3161 Modified to 110 MPH ... Retrieve Document
Asphalt Shingles Owens Corning Duration™ fiber glass-based asphalt shingles complying with ASTM zinc-coated, 16-gauge minimum with minimum 15/16” crown width. Staples must be long enough to ... View Doc
CHAPTER 9 ROOF ASSEMBLIES - ICC Safe
For normal application, asphalt shingles shall be secured to the roof with not less than four fasteners per strip shingle or two fasteners per individual shingle. Where the roof slope exceeds 20 units verticalin 12 units horizontal (zinc coated G90) ... Fetch Document
Asphalt shingle - Wikipedia, The Free Encyclopedia
An asphalt shingle is a type of wall or roof shingle. They are one of the most widely used roofing covers in North America because they have a relatively inexpensive up-front cost and are fairly simple to install. Use of such shingles for habitable structures is virtually unknown (or even ... Read Article
Galvanized Steel Halts Moss On Roof shingles - YouTube
Both copper and zinc (galvanized steel) halt moss growth on a roof. ... View Video
This Three-part Specification Must Be Edited To Delete ...
HERITAGE SERIES LAMINATED FIBERGLASS ASPHALT SHINGLES . This three-part specification must be edited to delete information and instructions not 1. ASTM A 653/A 653M - Standard Specification for Steel Sheet, Zinc Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip ... Fetch Full Source
STEEP SLOPE ROOFING - IKO Roofing Products
STEEP SLOPE ROOFING Section 07 31 13.13 Fiberglass-Reinforced Asphalt Shingles IKO TECHNICAL SUPPORT PROJECT: _____ ADDRESS Use galvanized (zinc coated) roofing nails, 11 or 12 gauge, ... Access Content
Shingle Application Instructions - 3-Tab Shingles
Never apply asphalt shingles to roof slopes less than 2:12 EAVE PROTECTION: Apply eave protection as per building code requirements, overhanging eaves by a nominal 1/4" a 3-Tab Shingles NAILING: Use galvanized (zinc coated) roofing nails, 11 or 12 gauge, with at least 3/8" diameter heads, ... Access Full Source
Alberta Allied Roofing Association Asphalt Shingle ...
Alberta Allied Roofing Association Asphalt Shingle Application Requirements Section 1 Roof Decks 1.1 General Asphalt Shingles are not permitted to be installed directly over rigid insulation. ... Access Content
SECTION 07 31 13 ASPHALT SHINGLES PART 1 GENERAL 1.01 SECTION ...
ASPHALT SHINGLES Project No. 15019 West Linn - Wilsonville School District August 2015 Rosemont Ridge Middle School 07 31 13 - 1 District A. Nails: Ring shank type, of hot-dipped zinc coated steel, 12 gage, 0.105 inch shank diameter, 3/8 inch head diameter, ... View Document
Laminated Shingles Application Instructions
Half-inch plywood is recommended for best deck performance. The installation of asphalt shingles on dimensional lumber Use galvanized (zinc coated) roofing nails, 11 or 12 gauge, with at least 3/8" diameter heads, Laminated Shingles Application Instructions ... Retrieve Here
Review Of Residential Roofing Materials, Part I
Various roofing materials. A website of the National Park Services (NPS 2003) Asphalt shingles come in various colors. Examples: Fiberglass shingles, dioxide (white), zinc ferrite (yellow), red iron oxides, carbon black, chrome ... Return Document
Copper Or Zinc Titanium - Construction Building Materials ...
Hip and Ridge Tile – Copper or Zinc Titanium or Pre-patina. Top roll . Valley metal (formed by Petersen Aluminum) Asphalt Shingles Made From Organic Felt and Surfaced with Mineral Granules / Asphalt Shingles Made From Glass Felt and Surfaced With Mineral Granules. ... Read Content
Commercial Roofing - DECRA Roofing Systems
Resistance of the aluminum-zinc alloy coated steel. The interlocking panels provide protection in commercial, institutional and residential applications where high performance, n Compared traditional asphalt shingles to stone coated steel shingles ... View This Document
Why You Shouldn't Mix Bleach And Vinegar - About.com Education
Mixing bleach and vinegar is a bad idea because it produces toxic chlorine gas. Here's what you should know about mixing bleach and vinegar, before you try it. ... Read Article
Tales From The North Side: Problems With Moss
Cedar shake roofs are more prone to moss problems than composition asphalt or metal roofs. 2 Zinc is available in three forms for roof installation to prevent moss: zinc zinc strips designed to slip beneath shingles, and zinc-impregnated composition roofing. The strips can be made of ... View This Document
Grand Sequoia® Shingles- Application Instructions
Grand Sequoia ® Application from reacting with asphalt shingles. ¥ FASTENERS: Use only zinc-coated steel or aluminum, 10-12 gauge, barbed, deformed or smooth shank roofing nails with heads 3/8" (10mm) to 7/16" (12mm) in diameter. Fasteners should be ... Read Here
No comments:
Post a Comment